View ST183S08PFL0_1317277.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Previous Datasheet
Index
Next Data Sheet
DISCRETE POWER DIODES and THYRISTORS
DATA BOOK
D-460
To Order
Previous Datasheet
Index
Next Data Sheet
Bulletin I25179/B
ST183S SERIES
INVERTER GRADE THYRISTORS Stud Version
Features
All diffused design Center amplifying gate Guaranteed high dv/dt Guaranteed high di/dt High surge current capability Low thermal impedance High speed performance
195A
Typical Applications
Inverters Choppers Induction heating All types of force-commutated converters
Major Ratings and Characteristics
Parameters
IT(AV) @ TC IT(RMS) ITSM @ 50Hz @ 60Hz I2t @ 50Hz @ 60Hz V DRM /V RRM tq range TJ
ST183S
195 85 306 4900 5130 120 110 400 to 800 10 to 20 - 40 to 125
Units
A C A A A KA2s KA2s V s C
case style TO-209AB (TO-93)
D-461
To Order
Previous Datasheet
Index
Next Data Sheet
ST183S Series
ELECTRICAL SPECIFICATIONS Voltage Ratings
Voltage Type number Code V DRM /V RRM , maximum repetitive peak voltage V
ST183S 04 08 400 800
VRSM , maximum non-repetitive peak voltage V
500 900
I DRM /I RRM max.
@ TJ = TJ max.
mA
40
Current Carrying Capability
Frequency
180 el 50Hz 400Hz 1000Hz 2500Hz Recovery voltage Vr Voltage before turn-on Vd Rise of on-state current di/dt Case temperature Equivalent values for RC circuit 570 560 500 340 50 V DRM 50 60
o
ITM 180 el 370 360 300 190 50 50 85 900 940 925 760 50 V DRM 60
o
ITM 100s 610 630 610 490 50 85 7040 3200 1780 880 50 V DRM 60
ITM
Units
5220 2280 1200 560 50 85 V A/s C A
47 / 0.22F
47 / 0.22F
47 / 0.22F
On-state Conduction
Parameter
I T(AV) Max. average on-state current @ Case temperature I T(RMS) Max. RMS on-state current I TSM Max. peak, one half cycle, non-repetitive surge current
ST183S
195 85 306 4900 5130 4120 4310
Units
A C
Conditions
180 conduction, half sine wave
DC @ 74C case temperature t = 10ms A t = 8.3ms t = 10ms t = 8.3ms t = 10ms t = 8.3ms KA2s t = 10ms t = 8.3ms KA2s No voltage reapplied 100% VRRM reapplied No voltage reapplied 100% VRRM reapplied Sinusoidal half wave, Initial TJ = TJ max
I2 t
Maximum I2t for fusing
120 110 85 78
I 2 t
Maximum I2t for fusing
1200
t = 0.1 to 10ms, no voltage reapplied
D-462
To Order
Previous Datasheet
Index
Next Data Sheet
ST183S Series
Fig. 1 - Current Ratings Characteristics
Fig. 2 - Current Ratings Characteristics
Fig. 3 - On-state Power Loss Characteristics
Fig. 4 - On-state Power Loss Characteristics
D-466
To Order
Previous Datasheet
Index
Next Data Sheet
ST183S Series
Fig. 5 - Maximum Non-repetitive Surge Current
Fig. 6 - Maximum Non-repetitive Surge Current
Fig. 7 - On-state Voltage Drop Characteristics
Fig. 8 - Thermal Impedance ZthJC Characteristic
Fig. 9 - Reverse Recovered Charge Characteristics
Fig. 10 - Reverse Recovery Current Characteristics
D-467
To Order
Previous Datasheet
Index
Next Data Sheet
ST183S Series
Fig. 11 - Frequency Characteristics
Fig. 12 - Frequency Characteristics
Fig. 13 - Frequency Characteristics
D-468
To Order
Previous Datasheet
Index
Next Data Sheet
ST183S Series
Fig. 14 - Maximum On-state Energy Power Loss Characteristics
Fig. 15 - Gate Characteristics
D-469
To Order
Previous Datasheet
Index
Next Data Sheet
ST183S Series
On-state Conduction
Parameter
V TM Max. peak on-state voltage
ST183S
1.80 1.40 1.45 0.67
Units
Conditions
ITM= 600A, TJ = TJ max, t = 10ms sine wave pulse
p
V T(TO)1 Low level value of threshold voltage V T(TO)2 High level value of threshold voltage r r
t1
V
(16.7% x x IT(AV) < I < x IT(AV)), TJ = TJ max. (I > x IT(AV)), TJ = TJ max. (16.7% x x IT(AV) < I < x IT(AV)), TJ = TJ max. (I > x IT(AV)), TJ = TJ max.
Low level value of forward slope resistance High level value of forward slope resistance Maximum holding current Typical latching current
m 0.58 600 1000 mA
t2
IH IL
T J = 25C, I T > 30A T J = 25C, V A= 12V, Ra = 6, I G = 1A
Switching
Parameter
di/dt Max. non-repetitive rate of rise of turned-on current t
d
ST183S
1000 1.1 Min 10 Max 20
Units
A/s
Conditions
TJ = TJ max, VDRM = rated VDRM ITM = 2 x di/dt TJ = 25C, VDM = rated VDRM, ITM = 50A DC, t = 1s
p
Typical delay time
s
Resistive load, Gate pulse: 10V, 5 source TJ = TJ max, ITM = 300A, commutating di/dt = 20A/s VR = 50V, t = 500s, dv/dt: see table in device code
p
t
q
Max. turn-off time
Blocking
Parameter
dv/dt IRRM IDRM Maximum critical rate of rise of off-state voltage Max. peak reverse and off-state leakage current
ST183S
500 40
Units
V/s mA
Conditions
TJ = TJ max., linear to 80% VDRM, higher value available on request TJ = TJ max, rated V DRM/V RRM applied
Triggering
Parameter
PGM Maximum peak gate power
ST183S
60 10 10 20
Units
W A
Conditions
TJ = TJ max, f = 50Hz, d% = 50 TJ = TJ max, t 5ms
p
PG(AV) Maximum average gate power IGM +VGM -VGM IGT VGT IGD VGD Max. peak positive gate current Maximum peak positive gate voltage Maximum peak negative gate voltage Max. DC gate current required to trigger Max. DC gate voltage required to trigger Max. DC gate current not to trigger Max. DC gate voltage not to trigger
V 5 200 3 20 0.25 mA
TJ = TJ max, t 5ms
p
TJ = TJ max, VA = 12V, Ra = 6 V mA V TJ = TJ max, rated VDRM applied
D-463
To Order
Previous Datasheet
Index
Next Data Sheet
ST183S Series
Thermal and Mechanical Specifications
Parameter
TJ T
stg
ST183S
-40 to 125 -40 to 150 0.105 0.04 31 (275) 24.5 (210)
Units
C
Conditions
Max. junction operating temperature range Max. storage temperature range Max. thermal resistance, junction to case Max. thermal resistance, case to heatsink Mounting torque, 10%
RthJC RthCS T
DC operation K/W Nm (Ibf-in) Nm (Ibf-in) g See Outline Table Non lubricated threads Lubricated threads Mounting surface, smooth, flat and greased
wt
Approximate weight Case style
280
TO-209AB (TO-93)
RthJC Conduction
(The following table shows the increment of thermal resistence RthJC when devices operate at different conduction angles than DC)
Conduction angle
180 120 90 60 30
Sinusoidal conduction
0.016 0.019 0.025 0.036 0.060
Rectangular conduction Units
0.012 0.020 0.027 0.037 0.060 K/W
Conditions
TJ = TJ max.
Ordering Information Table
Device Code
ST
1
18
2
3
3
S
4
08
5
P
6
F
7
N
8
0
9 10
1 2 3 4 5 6 7 8 9
- Thyristor - Essential part number - 3 = Fast turn off - S = Compression bonding Stud - Voltage code: Code x 100 = VRRM (See Voltage Ratings table) - P = Stud base 3/4" 16UNF-2A M = Stud base metric threads M16 x 1.5 - Reapplied dv/dt code (for tq test condition) - tq code - 0 = Eyelet terminals (Gate and Aux. Cathode Leads) 1 = Fast-on terminals (Gate and Aux. Cathode Leads) 2 = Flag terminals (For Cathode and Gate Terminals)
q
dv/dt - tq combinations available
dv/dt (V/s) 10 12 15 18 20 20 CN CM CL CP CK 50 DN DM DL DP DK 100 EN EM EL EP EK 200 FN * FM FL * FP FK 400 HN HM HL HP HK
t (s)
10 - Critical dv/dt: None = 500V/sec (Standard value) L = 1000V/sec (Special selection)
*Standard part number.
All other types available only on request.
D-464
To Order
Previous Datasheet
Index
Next Data Sheet
ST183S Series
Outline Table
CERAMIC HOUSING
16.5 (0.65) MAX.
N. (0. 9 .5 37
8.5 (0.33) DIA. 4.3 (0.17) DIA
2.6 (0.10) MAX.
C.S. 16mm 2 RED SILICON RUBBER 1 57 (6.18 ) 17 0 (6 .6 9 ) RED CATHODE WHITE GATE C.S. 0.4 mm (.0006 s.i.) 2 (.025 s.i.)
20
(0.
FLEXIBLE LEAD
79
)M
IN
.
)M I
Fast-on Terminals AMP. 280000-1 REF-250
215 (8.46) 70 ( 2.75 ) M IN . RED SHRINK 2 9 (1 .1 4) M A X. WHITE SHRINK
10 (0.39)
22.5 (0.88) MAX. DIA. 1 2.5 ( 0.49 ) M A X .
2 1 (0 .8 3)
M A X.
SW 27 1/2"-20UNF-2A 29.5 (1.16) MAX.
Case Style TO-209AB (TO-93)
All dimensions in millimeters (inches)
CERAMIC HOUSING FLAG TERMINALS
22 (0.89) 14 (0.55) DIA. 6.5 (0.25) 1 3 ( 0.5 1 )
8 0 ( 3 .1 5 ) M A X .
1.5 (0.06) DIA.
38 .5 (1 .5 2 ) M A X .
DIA. 27.5 (1.08) MAX.
2 7 .5 (1 .08 ) M A X .
1 6 (0 .63 ) M A X .
Case Style TO-209AB (TO-93) Flag
All dimensions in millimeters (inches)
SW 32
3/4"-16UNF-2A*
*FOR METRIC DEVICE. M16 X 1.5 - LENGHT 21 (0.83) MAX.
3 (0.12)
D-465
To Order

▲Up To Search▲

Price & Availability of ST183S08PFL0

	To Download ST183S08PFL0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .